Skip to main content

BENE2153-ANALOGUE ELECTRONICS

  • COURSE NAME :ANALOGUE ELECTRONICS
  • COURSE CODE :BENE 2153
  • CREDIT HOURS :3
  • PRE-REQUISITE :None
COURSE SYNOPSIS

This course will discuss:
BJT Transistor modeling, CE, CC and CB configuration, BJT small signal analysis, Feedback configuration, FET small-signal analysis, Frequency response, Bode plot, Bandwidth, Special amplifier: cascade, cascode, Darlington, multistage, differential amplifier circuit, Operational amplifiers: inverting, non-inverting, summing and buffer


LEARNING OUTCOMES

At the end of this course, students should be able to :
1. explain the fundamentals of small signal audio amplifiers.
2. design and measure using simulation tool response of single stage audio amplifiers using both
BJT and FETs.
3. analyze single stage and multistage amplifiers at mid-band, low and high frequencies.
4. analyze basic Op-amp circuits.

*work individually or in groups effectively to perform assignments/experiments.

REFERENCES

[1] Boylestad R., Nashelsky L., “Electronic Devices and circuit Theory”, Ninth Edition, Prentice
Hall Inc., 2006.
[2] S.H.Ruslan et.al. “ Elektronik II” Penerbitan UTM 1998
[3] Floyd, “Electronic Devices”, Sixth Edition, Prentice Hall, 2002.
[4] Theodore F. Bogart Jr., Jeffrey S. Beasley and Guillermore Rico, “ Electronic Devices and Circuits”, Sixth Edition, Pearson Education, 2004.

Kepada pelajar sesi 1-2009/2010 sila daftar sebagai ahli di http://groups.yahoo.com/group/UTeM_Reza untuk hebahan berkenaan kelas, tutorial, assignment dsnya.

Teaching Plan 2009/2010

Revision for TEST 2
Maklumat TEST 1 & Revision
Tutorial
1)Tutorial2.pdf
2)Tutorial3,4,5,6.pd



Lecture's Note
1)Chap1_Introduction.ppt
2)Chap1_decibel.rar
3)Chap1_Transistor Configurations (Summary).doc
4)Chapter1_loglinear paper.doc
5)ch3-BJT Modeling

Comments

Post a Comment

Popular posts from this blog

*******--Pengenalan Port Bersiri & Selari--*****

Port bersiri dan Port selari (Serial Port & Parallel Port) Dalam istilah perkomputeran, port bersiri merupakan antara muka pada sistem komputer, di mana maklumat dihantar dan diterima satu bit pada setiap masa (berlawanan dengan port selari ). Dalam sejarah komputer peribadi, kebanyakan pemindahan data menggunakan port sesiri dilaksanakan menggunakan piawaian RS232 menerusi kabel ringkas yang menghubungkan komputer kepada peranti seperti terminal atau modem. Tetikus, papan kekunci dan peranti-peranti lain juga disambungkan kepada hos tersendiri melalui cara ini. Antara muka seperti rangkaian ethernet, Fire Wire dan USB kesemuanya menghantar data secara sesiri, istilah "port bersiri" biasanya merujuk kepada perkakasan yang ingin berhubung dengan sesebuah modem atau sebarang peranti komunikasi yang sama. Dalam bab ini saya akan menerangkan berkenaan fizikal dan teori untuk kedua-dua peranti ini. Dari segi jenis, pin yang terdapat pada peranti ini dan kegunaannya...
1 comment
Read more

BENE 4143-MANUFACTURING AUTOMATION

MANUFACTURING AUTOMATION 1.0 LEARNING OUTCOMES At the end of the course, students are able to: 1.to explain the basic concepts of automation and its relationship with the manufacturing system. [PO1 , C2] 2.to design a manufacturing system based on control technologies, material handling and manufacturing systems concepts.[PO4, C5] 3.to analyze the quality control in manufacturing systems.[PO1, C4] 4.to analyze the manufacturing support systems that operates at the enterprise level.[PO3, C4] 5.to develop quality control (QC) in a manufacturing system using quality control tools. [PO5, C5] 6.to work effectively as an individually and collectively through group discussion.[PO8, A4] 1.0 SYNOPSIS This course will discuss the automation and control technologies, material handling, manufacturing support systems, quality control in manufacturing systems and manufacturing support systems. 2.0 PRE REQUISITE None 3.0 REFERENCES [1] Mikell P. Groover, Automation, Production Systems and Computer-In...
4 comments
Read more

DENE3353 (3 2010/2011)

DENE3353 (3 2010/2011) DENE 3353 APPLIED ELECTRONICS Type of Subject: P 1.0 Learning Outcomes At the end of this subject, the students should be able to: 1. explain the operation and the application of op-amp circuits. [PO1, C2] 2. analyze the operation of class A, class B, class AB and class C power amplifier circuits. [PO3 , C4] 3. demonstrate the three basic filter response characteristics and other filter parameters. [PO1, C3] 4. explain and analyze the operating principles of an oscillator and its application. [PO3, C2] 5. design simple power supply circuit and demonstrate the principles of voltage regulators. [PO3, C5] 6. measure the performance of applied electronic circuits through lab sessions. [PO2, P4] 7. perform experiments and present technical reports. [PO5, PO7,A3] 2.0 Synopsis This course will discuss about op-amp operations, applications and schematic diagrams, filter applications (basic filter concepts, filter response characteristics, acti...
Post a Comment
Read more